Advertisement
Transcript

Construct a Hurricane-resistant Pergola in Your Back Yard to Improve a Bare Corner and Add a Shaded Sitting Area

Dress up a plain corner of your backyard with a free-standing pergola that is visually appealing and offers a shaded sitting area as well. Make it large enough to accommodate lawn furniture or even a hot tub along with hanging flower baskets and climbing vines. Construct it according to building codes and make it stout enough to withstand hurricane winds!

Read More
Advertisement
tying string to the first corner stake
Step 1

Check for Gas, Water, and Electric Lines before Locating Posts

Determine where to sink the pergola's six support posts after checking for gas, water, or electric lines. Drive a stake and string at the first corner. The six-by-six posts must be aligned perfectly straight and parallel to each other.

aligning the string for a temporary stake at the back corner
Step 2

Align a Back Corner Stake with String and Triangle

Position a large layout triangle along a two-by-two at the pergola's front edge. Stretch string to the back corner, ensuring that the angle at the front stake is 90 degrees. Align a stake at the back corner. This pergola/arbor design is rectilinear.

tying markers along the string for post positions
Step 3

Tie Markers along the String to Mark Pergola Post Positions

Tie markers along the string for the middle and back post positions on that side of the arbor. Equally, space them with a tape measure. Repeat for three post positions on the other side. Drive a stake at each marker.

marking posthole positions with powdered chalk lines
Step 4

Mark Post Holes with Powdered Chalk and a Bottomless Bucket

Center a bottomless bucket on each of the six stakes and sprinkle powdered chalk around the outside perimeter to mark a posthole digging line. Carefully remove the stakes without disturbing the digging line for each posthole.

Advertisement
digging post holes to meet building codes
Step 5

Dig Holes at Least 3-Feet Deep with a Posthole Digger

Dig six holes within the chalk lines with a posthole digger, making them slightly deeper than 3 feet. Building codes in this hurricane-prone area require that holes be at least 3-feet deep to keep the posts stable in high winds.

clamping posts to hold them vertical
Step 6

Set Posts in the Holes and Ensure They Are Plumb

Add 2-3 inches of crushed rock to holes to promote drainage and prevent wood rot. Drop six-by-six posts into holes. Ensure pergola posts are plumb with a post level. Clamp temporary braces to stakes and posts to hold them vertical.

pouring dry concrete mix into postholes
Step 7

Pour in Dry Concrete Mix and Add Water

Fill each posthole with dry concrete mix and add a gallon of water to each. Be careful to keep it off the exposed upper portion of the posts. We used Quickcrete, a quick-drying concrete that requires no mixing.

positioning beams to sandwich the post tops
Step 8

Attach Temporary Supports to Bear the Weight of Two Beams

Attach temporary horizontal supports to hold up the two chamfered beams sandwiching each row of side posts. Pre-drill two holes through the side beams and posts for carriage bolts. Stagger them so they are less likely to split the posts.

driving in carriage bolts
Step 9

Drive in Carriage Bolts and Secure with Nuts and Washers

Drive carriage bolts through the holes with a club hammer and secure the bolts with nuts and washers on the outside surface of the side beams. Tighten the nuts with a socket wrench until the wood begins to compress.

positioning hurricane clips
Step 10

Attach Cross Beams with Hurricane Clips

Chamfer the cross beams and position them on top of the side beams, equally spaced from the pergola's front to its back. Attach them with metal hurricane ties held temporarily with a screw until you hammer in hot-dipped galvanized bracket nails.

Advertisement
Advertisement

Related Tips

Blog Articles

November 04, 2024

DIY Shutters That Last: Building with Azek

Ever thought about adding a touch of timeless charm to your home’s exterior? Shutters can do just that, enhancing your windows while adding a stylish flair. Brian recently embarked on a DIY journey to create shutters using Azek, a PVC material that mimics wood’s beauty but with enhanced durability and low maintenance.

November 01, 2024

Adhesives: A Comprehensive Guide

Navigating the world of adhesives can be daunting with so many options available. Having a basic understanding of the different types and their applications can make the decision-making process much easier. In this blog post and accompanying video, we will break down various types of adhesives and how to use them effectively.

October 17, 2024

Creating a Glossy Bar Top Finish: A DIY Guide

Have you ever wanted to elevate the look of your home bar that looks like liquid glass? A glossy bar top can add a touch of sophistication and style to your space. In this DIY guide, we will walk you through the steps to create a stunning glossy bar top that will impress your guests and elevate your home entertainment experience.

Advertisement
Recent Articles
Advertisement
Advertisement